83mm Build Update

Hello everyone welcome back. Todays video is an update on the new 83mm brushless build I have been working on. I added a new camera mount. New standoffs so its not so tall. I also added motor guards and landing gear. Here are the full specs for the build BetaFPV 83mm Carbon Fiber Frame Recommend motors: 1102 1103 1104 brushless motors Wheelbase: 83mm Plate Thickness:2.0mm Weight: 10g Form Factor: 16mm x 16mm http://amzn.to/2i9CyPZ USAQ Betaflight F3 Micro 6A 2S 4-In-1 Brushless ESC OSD Flight Controller Micro Cube Flight Controller Specifications: Dimensions: 20*20mm Mounting Dimensions: 16*16mm Weight: 1.9g Processor: STM32F303CCT6 (72MHZ, 256K FLASH) Sensor: MPU-6000 ( connected by SPI) Firmware version: betaflight_3.1.0_OMNIBUS Built-in BEC: 5V/0.5A Receiver: PPM, Spektrum 1024/2048, SBUS, IBUS, XBUS, SumD SumH RX etc. Power supply: 2S lipo battery ( 6.5V-8.4V) Suitable for 60mm-80mm mini brushless FPV Quadcopter frame ESC Specifications: Item name: 4 In 1 6A BLHeli_S ESC Size: 25x29mm (includes solder pad) Mounting holes: 16x16mm, φ2mm Weight: 3g Input voltage: 2S lipo Con. Current: 6A Peak Current: 10A (5S) Firmware: BLHELI_S Processor: SILABS EFM8BB21F16G BEC: NO Driver: 3 in 1 MOS Supports Dshot Oneshot multishot Features: -Support programmable LED Sprit (turn off transponder before using) -Support BLheli/BLHELI_S suite Pass-through ready -Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 -Default Dshot600 -Built-in voltage detection, alarm -Built-in Betaflight-OSD -Buzzer solder pin -LED_STRIP connector Package included: 1* Super_S F3 flight control board 1* Super_S BS06D 6A 4in1 ESC 8*M2*5+5 Nylon column 8*M2 Nuts 8*M2 Screw http://amzn.to/2yd5fT1 BetaFPV 1103b 10,000kv Brushless Motors Height: 15mm Width: 13.6mm Weight: about 3.7g Shaft: 1.5mm KV: 10000KV No longer available via BetaFPV. Here are some similar motors http://amzn.to/2yfmxip BetaFPV 1735 4 Blade Props Material: PC plastic Length: 1.7 inch, about 43.2mm Color: white, orange, purple, green, blue, red Mounting hole: 1.5mm Weight: 0.8g per piece Applicable for 1102, 1103, 1104, 1105, 1106, 11xx motors http://amzn.to/2zVWC0m BetaFPV H01 AIO FPV Camera Output power: 25mW Supply Voltage: 2.9-5.5v Weight: 3.6g Antenna: Dipole Frequency: 5.8GHz 40 Channels FOV: 120 http://amzn.to/2i9DuDZ M2 Standoff kit http://amzn.to/2yfXFGY Motor Guards by Makerfire http://amzn.to/2zDdD2u Camera mount for 16mmx16mm by RJX Hobby http://amzn.to/2yeSHKI BetaFPV 450mah 2s Lipos http://amzn.to/2yFlkoQ If you have any questions about this build feel free to leave me a comment. Check out my Blog. www.craytech.blog Dont forget to enter to win the BetaFPV 65s Frame Kit Giveaway. https://youtu.be/kb0AHAjpPTw Like & Subscribe Thanks for watching Fly Safe & Fly Often Music by Ryan Little Sub his channel https://www.youtube.com/user/TheR4C2010